COMedia KCB datasheet, Master PIR Control Chip (6-page), KCB datasheet, KCB pdf, KCB datasheet pdf, KCB pinouts. KCB Datasheet, KCB PDF, KCB Data sheet, KCB manual, KCB pdf, KCB, datenblatt, Electronics KCB, alldatasheet, free, datasheet. KCB datasheet, cross reference, circuit and application notes in pdf format.

Author: Shakataxe Dik
Country: Cape Verde
Language: English (Spanish)
Genre: Travel
Published (Last): 9 May 2013
Pages: 299
PDF File Size: 17.82 Mb
ePub File Size: 20.75 Mb
ISBN: 205-1-92998-740-9
Downloads: 13708
Price: Free* [*Free Regsitration Required]
Uploader: Maushicage

Auto-OFF mode can be disabled. If Auto-ON mode is disabled, the load will turn on if there is motion within 6 seconds after turn-off.

Adjustable daylight detector disables Auto-ON during daytime. The value of the pot dataheet not critical and any value between M Four main operating modes can be used in any combination: F Internal switched capacitor bandpass filter reduces external component count and improves reliability by. The MPCC has been designed for easy implementation. C High sensitivity PIR input with special noise cancellation circuitry.

The filter response can be measured in this way. Load turns off manually, with a momentary contact switch.

Due to its high sensitivity and. Load turns on manually, kf778b a momentary contact switch. Pin 8 Pyro S is a sensitive node and the external interconnect to this pin should be made as short as possible. B Low cost solution for PIR motion control switching applications. Adjustable OFF timer activates whenever motion stops. The Sensitivity Adjust pot is used to select a voltage between the pyro drain reference voltage minimum. Load turns on manually, with a momentary contact switch. J Adjustable daylight detector sensitivity.

  ANEURISMA EN EL POLIGONO DE WILLIS PDF

Daylight detector can be disabled. Due to its high sensitivity and. A Circuit design maximizes performance while minimizing external component count and board layout space. Load turns on when motion is detected adjustable sensitivity. J Adjustable daylight detector sensitivity. I Daylight detector circuitry is designed to use either silicon photo diode or CdS detector.

Adjustable OFF timer activates whenever motion stops. Load turns off manually, with a momentary contact switch. If Auto-ON mode is disabled, the load will turn on if there is motion within 6 seconds. If the load goes off because you stopped moving reading a book for.

KC778B Datasheet PDF

Load turns on when motion is detected adjustable sensitivity. E Adjustable PIR sensitivity.

If the load goes off because you stopped moving reading a book for exampleyou have 6 seconds to wave your arm to turn the load back on. If the load goes off because you stopped moving reading a book for. E Adjustable PIR sensitivity. H High immunity to line frequency noise. The MPCC has been designed for easy implementation. Auto-OFF mode can be disabled.

Auto-ON mode can be disabled. Load turns off if there is no motion during the time delay. H High immunity to line frequency noise.

  AS BRUMAS DE AVALON VOL 4 PDF

KCB Datasheet PDF

The Sensitivity Datasneet pot is used to select a voltage between the pyro drain reference voltage minimum sensitivity and Gnd maximum sensitivity. I Daylight detector circuitry is designed to use either silicon photo diode or CdS detector. Adjustable daylight detector disables Auto-ON during daytime. Disconnecting the external capacitor prevents motion from being detected.

Due to its high sensitivity and reliability, it is also widely used in security product. Daylight detector can be disabled. Auto-ON mode can be disabled.

D Choice of two PIR gain settings: Due to its high sensitivity and reliability, it is also widely used in security product. C High sensitivity PIR input with special noise cancellation circuitry. B Low cost solution for PIR motion control switching applications. If the load goes off datasneet you stopped moving reading a book for exampleyou have 6 seconds to wave your arm to turn the load back on.

This node should also be closely surrounded by a ground plane. F Internal switched capacitor bandpass filter reduces external component count and improves reliability by minimizing sensitivity to external component values.