Cardax FT Controller – Download as PDF File .pdf), Text File .txt) or read online. Installation Guide. Cardax FT Controller CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you. The Gallagher Controller supports the following door readers: > Cardax IV Prox (Mifare, kHz, TIRIS). > Cardax IV Prox Plus (Mifare, kHz,. TIRIS).

Author: Tuzil Zulkilmaran
Country: Guatemala
Language: English (Spanish)
Genre: Sex
Published (Last): 3 January 2005
Pages: 454
PDF File Size: 11.74 Mb
ePub File Size: 6.38 Mb
ISBN: 123-3-32459-479-2
Downloads: 9550
Price: Free* [*Free Regsitration Required]
Uploader: Zululabar

Before you beginShipment contentsCheck the shipment contains the following items: Wait for the Run LED to stop flashing. It is an Ethernet attached device which connects to a server, however it can operate autonomously. Follow the steps below to access the Controller’s Config web page: This operation can only be reset by the factory of manufacture.

The Settings in bold specify the default new installation startup configuration. Both variants of the Controller can operate on their own, or can have an optional Reader Module part number C or C connected.

Cardax Ft Controller 6000pdf

Refer to the “Component layout” within this Installation Note for wiring this plug. A dial-up modem may be used for communication if network communications are not available. Part number 3E R1 August Revert to the factory default version of the operating system. Install all the system and power cables. The sequence completes fairly quickly but it is important you ensure the LED finishes indicating the “normal running” sequence.

On-board termination is optional using termination jumpers. Gallagher Controllers Overview The Gallagher Controllers are intelligent field controllers, programmed to make access control and intruder alarm decisions in the field, independent of the Gallagher Command Center.

  CVSTRACK FILETYPE PDF

On startup configuration and the IP address is deleted. Integrated Access Control and Intruder Alarms capability 2. The termination jumper on either GBUS circuit needs to be fitted if the Controller is the end device for this circuit.

Cardax Ft Controller pdf

Looking at the Controller it will be obvious that the there is no ethernet activity on either ethernet connection, as the RJ45 connector LEDs will not be operating, and the Controllers run LED will be in 2 flash.

Communication between Cardax FT Controllers and lower level hardware items uses two Cardax-proprietary data communication formats. Card readers Intruder Alarms may be installed in elevator cars to Documents. The Gallagher Controller R has on-board connections for with variations for the Gallagher Controller R shown in brackets:.

The cables should stow neatly and be held in place by the cable clamps fitted into the base of the Cabinet. The software is powerful, The Cardax FT Controller integrates much of the functionality of the original Providing flexible configuration options to meet specific site requirements, Gallagher Controllers:.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. On-board connections are provided for: Click the OK button. Initialise the Cardax FT Controller The Enter Network Password screen displays. High Spec variant only The High Spec variant of the Controller has a secondary Ethernet connection link to which communications can automatically be switched upon failure of the primary Ethernet connection.

Changes or modifications not expressly approved by Gallagher Carxax Management Systems could void the user’s authority to operate this equipment.

The Cabinet door must remain closed for at least one minute for the initialisation of the optical tamper detectors to be cradax. When using these connection points, ensure the Power Supply to the Cardax FT Controller is capable of supplying the extra current required. In the event of a catastrophic failure, after approximately 60 seconds the In-Service relay opens.

  HAYT KEMMERLY ANALISIS DE CIRCUITOS EN INGENIERIA PDF

Page 2 1 November Introduction Optical tamper detectorsThe front optical tamper detector will sense when the Cabinet door is opened.

Operating temperature Humidity Maximum number of The Gallagher Controller is specifically designed to support access controlled doors and integrated intruder alarms.

No private key or vardax loaded. Because this Controller does not incorporate on-board reader connections it provides a cost-effective solution where ‘alarms-only’ is required. When the Cardax FT Controller is re-powered after servicing and is operating correctly, the optical tamper detectors will be re-initialised.

This means in the event of network communications being disrupted, security is maintained on site. However, this DC voltage out will be approximately 1 volt lower than the voltage supplied to the Cardax FT Controller Cardax FT Version 5.

Gallagher Controllers | AES Group Ltd.

Set switch 2 to ON closed. Cardax Ft Controller pdf Download Report. Plug-in ModemThe Cardax FT Controller has an on-board connector Serial for a plugin modem part number C which is purchased separately from the Controller cardac The rear optical tamper detector will sense if the Cabinet is removed from its mounting position.

Set switch 2 to OFF open. Cardax FT for Airport Security.